Page 1 of 1

Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3 EFI

PostPosted: Sun Aug 20, 2017 9:32 pm
by Scrap Metal
Hey guys, I blew up my gen2 sooner than I was hoping and I do not have time to properly build a motor at this point in my life so I am going with the easier/quicker gen4 motor swap for now. All parts are brand new open box, unless otherwise stated.

BRAND NEW
1. MAHLE Pistons TOY378405I04 86.50mm (~$600) Price Reduced $450shipped
2. EAGLE Rods 5.428 CRS5428T3D (~$375) $275 Shipped SOLD
3. ACL Race Main, Rod & Thrust Bearing Kit 5M8361H 4B8366H 2T1689 (~$130)$100 Shipped SOLD
4. ARP Main Stud Kit 203-5404 (~$120) $90 Shipped
5. ARP 3S-GTE Head Stud Kit 203-4204 (~$150) $100 Shipped SOLD

USED PARTS
1. gen2 3sgte Engine Block $100
2. gen2 3sgte Cylinder Head Stock cams $200

3. COMPLETE GEN3 EFI SETUP RUNNING ON GEN 2 3sgte $550 SOLD
Converted Gen 2 Harness, ECU, 540cc, AIT Sensor, MAP Sensor, COIL, etc... pretty much everything you would need, this was running on my gen2 3sgte until I ran it out of oil. I'm going gen4 swap so I don't need this.

Parts Located in SoCal 91761 Paypal, cash, venmo...

Image
Image

Image

Image

Image
More pics coming, in process.....

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Sun Aug 20, 2017 11:02 pm
by Tecker185
What did the gen3 efi setup come off of?


Sent from my iPhone using Tapatalk

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Sun Aug 20, 2017 11:37 pm
by Scrap Metal
its currently on my alltrac. it was running great until i tan the motor out of oil lol... it was an old gen2 anyway... instead of building a gen 2 block like i had planned I'm just going with an st215 motor so i don't need any of these parts

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Sun Aug 20, 2017 11:49 pm
by Tecker185
What year alltrac


Sent from my iPhone using Tapatalk

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Mon Aug 21, 2017 12:15 am
by Scrap Metal
woops... forgot to list that

st185 1990

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Mon Aug 21, 2017 6:44 pm
by Tecker185
Haha so will that include everything to get my 90 running on gen3 efi?


Sent from my iPhone using Tapatalk

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Mon Aug 21, 2017 7:56 pm
by Scrap Metal
Yeah, this was running perfect on my gen2 st185. Only check engine light I got was the speed signal due to my failing speedometer. It will come with everything including the MAT sensor in the throttle body (didn't list that in the ad). I believe its either ATS or Berktechnology that makes the adapter I'm using.

Basically I would be giving you the injectors and rail, and all the sensors needed. The engine harness and ECU.

The wiring was actually done by the previous owner, his board name is tubasteve if you want to see his build thread on the red st185, it is the one I own now.

At the ECU he spliced the wires himself with connectors, I never had any issues, check engine light worked like it was supposed to, some people prefer buying a patch harness to go in between, but this one doesn't have that.

Actually, I just remembered, the only thing you will need is the Intake temp sensor that goes near the filter. The one currently on it is a smaller version that doesn't fit snugly in the stock size piping... these IAT sensors are readily available though so it shouldn't be a big deal, as you should already have one currently.

Everything is still on the car. Recently I did repair the distributor plug wire that got caked in oil and one of the pins slid out, so as far as the harness goes I would make sure that its still snug when you plug in the dizzy.

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Mon Aug 21, 2017 8:30 pm
by Tecker185
I sent you a pm


Sent from my iPhone using Tapatalk

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Tue Aug 29, 2017 6:23 am
by Scrap Metal
GEN3 EFI, EAGLE RODS, ACL BEARINGS, ARP HEADSTUDS ARE ALL SOLD

MAHL Pistons and ARP Main Stud Kit still available. Make me an offer!!!

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Wed Aug 30, 2017 4:27 pm
by awdmofo
PM sent, I think I'll take the ARP kit you have :D .

Re: Brand New Motor Build Parts! Mahl, Eagle, ACL, ARP, GEN3

PostPosted: Tue Sep 05, 2017 2:14 am
by Scrap Metal
Price Reduced!

MAHL PISTONS $450 SHIPPED!