Page 1 of 3

3SGTE CAMRY UPDATES

PostPosted: Sat May 21, 2011 5:23 pm
by CAMRYGT4
Once again its been awhile since I posted on hear, but here are some pictures, mod list, and dyno sheet.
also just got a MAPECU-3 so hopefully after I get it on the dyno again and tune the car we can break the 300 awhp barrier.

Mod list:
1990 3sgte swap
MLS head gasket
Maule pistons .020 over 9to1 compression
Shot peened stock rods
ARP fasteners
Block was fully prepped from individually matched cylinder bores
to the ultra smooth deck for the the MLS head gasket
Fully balanced rotating assembly
Flow tested and balanced injectors
MAPECU-3 fuel management
ACL race barrings
Turbo upgrade to ct20b
ATS throtle body inlet
Front mount intercooler
Coustom dule core aluminum radiator
HKS SSQ BOV
Greddy ProfecB boost controller
Aromotive fuel pressure regulator
Lightened race flywheel and sprung hub six puck racing clutch
SS clutch line
Short throw shifter
Boost gauge and wide band AFR gauge
Wheels 16" drag dr-31 16x7 40mm offset
Tires 225/45/16 BFGoodrich kdw2
matching full size spare
Megan street dampener coil-overs for an st185 Celica Alltrac
EBC yellow stuff Pads
Cross drilled and slotted Brembo rotors
Custom SS braided brake lines
3" catles down pipe
Full 3" mandrel bent exhaust
18% window tint
Battery relocated to trunk
HID lighting
New leathger interior
New paint
JDM rear spoiler
V6 front air dam
De badged
Pioneer AVIC dvd nav
Boston speakers
Alumapro sub

Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image

Re: 3SGTE CAMRY UPDATES

PostPosted: Sat May 21, 2011 7:45 pm
by toayoztan
Clean, I like it. Any videos?

Bryan

Re: 3SGTE CAMRY UPDATES

PostPosted: Sat May 21, 2011 9:46 pm
by YerRandO
Amazing project!

Re: 3SGTE CAMRY UPDATES

PostPosted: Sun May 22, 2011 12:21 am
by CAMRYGT4
thanks guys! sorry no video yet but I plan to take video of my next dyno session.

Re: 3SGTE CAMRY UPDATES

PostPosted: Mon May 23, 2011 3:21 pm
by UtahSleeper
Nice trac. Any reason for still running the stock MAF?

Re: 3SGTE CAMRY UPDATES

PostPosted: Mon May 23, 2011 4:25 pm
by CAMRYGT4
3tcpower wrote:Nice trac. Any reason for still running the stock MAF?

Thanks. The stock MAF is going away on Thursday when I install my MAPECU-3, in fact I bought it new last year if anyone needs one I'll sell it for 100 bucks.

Re: 3SGTE CAMRY UPDATES

PostPosted: Tue May 24, 2011 1:57 pm
by YerRandO
CAMRYGT4 wrote:The stock MAF is going away on Thursday when I install my MAPECU-3, in fact I bought it new last year if anyone needs one I'll sell it for 100 bucks.


PM sent

Re: 3SGTE CAMRY UPDATES

PostPosted: Wed May 25, 2011 7:56 pm
by GMan
Beautiful Project :D

Regards;

Re: 3SGTE CAMRY UPDATES

PostPosted: Wed May 25, 2011 11:21 pm
by 88gt4DE
Very Impressive man ... I love it ... I need to get some leather work like you :notworthy:

Re: 3SGTE CAMRY UPDATES

PostPosted: Thu May 26, 2011 4:44 am
by CAMRYGT4
88gt4DE wrote:Very Impressive man ... I love it ... I need to get some leather work like you :notworthy:


Thanks I got the seat kit from leatherseats.com, when I ordered it they told me that they hadn't had an order for the kit for this car in over a decade.

Re: 3SGTE CAMRY UPDATES

PostPosted: Thu May 26, 2011 7:22 pm
by 88gt4DE
CAMRYGT4 wrote:
88gt4DE wrote:Very Impressive man ... I love it ... I need to get some leather work like you :notworthy:


Thanks I got the seat kit from leatherseats.com, when I ordered it they told me that they hadn't had an order for the kit for this car in over a decade.


I believe that ... got this local guy lined up to do mine over next winter ... we will see :)

Re: 3SGTE CAMRY UPDATES

PostPosted: Sat May 28, 2011 5:56 am
by CAMRYGT4
My next mods will be powder coating various engine bay parts, cryo treating my rotors, and building my spare cyl head.

Re: 3SGTE CAMRY UPDATES

PostPosted: Fri Jul 08, 2011 3:59 pm
by fernando8877
Thats a killer build you got going. I like the look too. :notworthy:

Re: 3SGTE CAMRY UPDATES

PostPosted: Tue Aug 23, 2011 1:54 am
by JeanR
Big project you got there. :)

Re: 3SGTE CAMRY UPDATES

PostPosted: Fri Sep 09, 2011 5:45 am
by CAMRYGT4
So here is an update of what's going on.

The car has been on back on the road since early august with a street tune. the street tune is OK but there are some holes in the map, so were going to have to put the car on the dyno (its tough to do a fifth gear pull at 125mph in traffic). So the car hits the dyno next Wednesday the 14th at drift office.

Here are some photos and descriptions of what iv been up to the last couple of months.



here are a couple of tear down pictures
Image
Image
Image
Image

progress photos, and yes red calipers do make you go faster :lol: .

Fresh EBC yellow pads and cryo treated rotors
Image

parts back from powder coating, the pics don't do them justice the pipes and heat shield are a graphite color with flake in it so in the sun it really sparkles and everything has a wrinkle finish.
Image
Image
Image
Image
Image
Image

Unexpected mods! my friend sold me two Alpine amps at a price I couldn't refuse. I replaced my single anemic Clarion 250w amp with an 850w mono for my Alumapro sub and added a 450w 4chanel amp for my front and rear speakers. Everything sounds so much clearer at high volume. sorry about the crappy picture, at the time this picture was taken the install was not complete.
Image

Here are a couple of pictures I took the day we did the street tune. At the gas station of course, it took almost two tanks.
Image
Image

And here are some from Puget Sound Toyota Owners Festival on August 14th
Image
Image
Image
Image
Image
Image
I was lucky enough to win a ribbon again this year. For (Best Other) There weren't enough Camry's there this year for us to get our own category so I had to compete with some pretty cool and rare cars.
Image