Page 10 of 10

Re: Phattyduck's SV25/ST205 hybrid

PostPosted: Fri Dec 11, 2015 4:22 pm
by phattyduck
CSAlltrac wrote:What hose did you use for the remote filter? The blue stuff.
Its -12AN Aeroquip push-loc hose. It comes in black or blue. Actually, that reminds me that I should probably replace that hose in the near future... After around 8 years now (two different engine bays), it is starting to crack a bit around the outside. I'll probably go black when I replace it.

-Charlie

Re: Phattyduck's SV25/ST205 hybrid

PostPosted: Fri Dec 11, 2015 4:34 pm
by phattyduck
CTechBlueDragon wrote:Wow man where did you source those parts? I have been looking for a while and I can't find anything. I am not looking to do the front conversion you did, I hate to say it but I think the car looked a lot cleaner when you first got it. The bumper would be fine if it were painted to match. I guess the other stuff is up to your taste. I have been looking at pictures of the GLI and GXI and they have a really nice looking rear valance piece(s) we never got, any idea where I could source one? I would also like a GLi or GXi badge for the rear but I cannot even find that. lol It also looks like they had some sort of stock side skirts also...
The spoiler will definitely go on at some point. I don't want to do that before its painted though - I don't want to deal with mounting it a second time. The whole front end (including the hood) will get painted at some point. It should tie it together much better than it currently is. I pretty much need to run the JDM bumper to get any airflow to the intercooler, so it has to stay.

I'm not sure if the Euro/Aussie/JDM rear valence pieces would fit - the F/R bumpers are different in countries that didn't have the 5-mph bumper rules.

As for where I got the parts - almost all of them were bought from other guys that imported them and never installed them... I have been on the Camry forums collected parts for 15+ years now.

-Charlie

Re: Phattyduck's SV25/ST205 hybrid

PostPosted: Fri Dec 11, 2015 5:07 pm
by de_engineered
I'm curious where the CF hood came from :D

Re: Phattyduck's SV25/ST205 hybrid

PostPosted: Fri Dec 11, 2015 5:14 pm
by phattyduck
de_engineered wrote:I'm otherwise curious where the CF hood came from :D
There was a group-buy done around maybe 2001 for a set of 10... only 6 got made and the company that did them went out of business... I got the hood used from the guy that organized the group-buy years later. Not sure what happened to the rest of them.

-Charlie

Re: Phattyduck's SV25/ST205 hybrid

PostPosted: Fri Dec 11, 2015 5:20 pm
by de_engineered
Copy that. I've looked at DIY and shop options, they're all pretty pricey in small, or well, any quantity. The stock hood is so darn heavy though (there's aluminum, not without its own cost if less than CF).

Re: Phattyduck's SV25/ST205 hybrid

PostPosted: Tue Jul 25, 2017 7:25 pm
by phattyduck
Thank you photobucket!! All the pics in the thread have been updated.

Lots of changes recently in life. A new baby will do that!

The Alltrac has mostly been sitting quietly under a cover for nearly the last year. Did some maintenance, got the clutch clevis welded up:

Before, with visible wear from internal rubber disintegrating:

Image

And all welded up:

Image

Image

I have been contemplating selling the Alltrac... But I don't know if anybody else would appreciate it like I do. I have a '99 4Runner now that has been 4WD swapped. It is begging for a 2jz swap now. Maybe the Alltrac goes back to daily driver status for that project. :D

-Charlie

Re: Phattyduck's SV25/ST205 hybrid

PostPosted: Wed Jul 26, 2017 4:44 am
by FC Zach
phattyduck wrote:Thank you photobucket!! All the pics in the thread have been updated.


I've noticed this. . I would suggest Flickr in the future if PB is bad about doing this.