How to disassemble mirrors (+ question about convex glass)

For everything related to the inside of the car!!

How to disassemble mirrors (+ question about convex glass)

Postby Practical » Fri Oct 22, 2004 7:55 pm

So I have my european mirrors that I want to put on my US car. The european mirrors have five wires going to each while my US car only has 3 wires going to each mirror, probably because the Euro ones are heated. I realize that nobody can help me with the wiring colors, so I will have to investigate on my own. To that end, I was thinking to pull the mirror glass off so I can see where each wire goes and reverse engineer what is going on.

But can I just yank off the glass? I don't want to break anything. Is there a way to snap of the glass without breaking it?

To answer another question which was posed by someone in response to my earlier post, convex glass is like on the US p/s. The euro mirrors look like this:

http://www.streetracing.by/bestauto/200304/04.jpg

And no, convex European mirror glass has a different outline than US glass so it will not fit in a US mirror.

Thanks,
Members don't see the above ad. Register now - it's free!
Practical
Practical
Club Member
 
Posts: 21
Joined: Thu Oct 21, 2004 9:40 pm
Location: Baltimore, MD, USA

Postby alltracman78 » Sat Oct 23, 2004 1:09 am

If it's just heated glass, it might not matter which is pos and which is neg, unless there's a diode somewhere in it.
Image
User avatar
alltracman78
GTFour God
 
Posts: 4681
Joined: Mon Aug 09, 2004 9:04 am
Location: Ma

What I meant was...

Postby Practical » Sat Oct 23, 2004 11:55 am

the mirror has a five-connector mini plug, the car has a three connector plug. I don't know what wires go to what in the mirror (motors, heater, etc.). That's why I want to take the glass off the mirror to find out what each wire is for so I can wire the new mirrors up correctly to my car's harness and adjust the mirrors with the existing button. I understand that a heating element doesn't care about polarity, but I wasn't planning to connect it anyway.

Now can anybody tell me if (and how) I can take off the mirror glass and put it back on without breaking it?
Thanks,
Practical
Practical
Club Member
 
Posts: 21
Joined: Thu Oct 21, 2004 9:40 pm
Location: Baltimore, MD, USA

Re: What I meant was...

Postby falken_gt4 » Sun Oct 24, 2004 8:28 am

Practical wrote:the mirror has a five-connector mini plug, the car has a three connector plug. I don't know what wires go to what in the mirror (motors, heater, etc.). That's why I want to take the glass off the mirror to find out what each wire is for so I can wire the new mirrors up correctly to my car's harness and adjust the mirrors with the existing button. I understand that a heating element doesn't care about polarity, but I wasn't planning to connect it anyway.

Now can anybody tell me if (and how) I can take off the mirror glass and put it back on without breaking it?
Thanks,


I'm sure mine has a 5 pin plug, it is electrically folding? Don't know if it is the same as an ST205? I know cos I bought a non folding one that had only three wires with a small plug and my one has a bigger plug with 5 wires I think.

Cheers
Andy
Andy MacRae
'94 Celica GT4 JDM ST205 (silver)
'90 Civic 1.4GL UKDM EC9 (white)
PerthShire, Scotland
http://www.r-spec.co.uk

Image
falken_gt4
Club Member
 
Posts: 60
Joined: Tue Sep 07, 2004 10:48 pm
Location: Scotland, UK

Just flip it up

Postby Practical » Sun Oct 24, 2004 5:46 pm

I worked out the answer to my question. The glass comes off by carefully prying it off beginning from the bottom (it is hinged at the top). If you don't start from the bottom, it will break. Don't ask me how I know.
Practical
Practical
Club Member
 
Posts: 21
Joined: Thu Oct 21, 2004 9:40 pm
Location: Baltimore, MD, USA


Return to Audio / Wiring / Interior

Who is online

Users browsing this forum: No registered users and 0 guests

cron