project alltracst185 update! 6/15/14 rust is gone!!! :)

Talk about your project car here

project alltracst185 update! 6/15/14 rust is gone!!! :)

Postby alltracst185 » Fri Aug 10, 2007 3:17 pm

I was bored and decided to look at my project thread and thought it was boring. I had to freshen it up since i hadn't showed any of my good parts since i got them. so basically I'm starting over again.....enjoy

cs/rc hood part # 53301-20400
cs/rc hood bulge part # 76181-20901
CCW's
18x10
255/40/17

this is what my 1990 all-trac when i first saw her
Image
It's a picture of a picture so not so good.


This is when my wallet took the hit!

I have started my turbo install the top mount was on in the first pic, here are some pics. i'm going to move the wastegate down and to the left a little so the hood will close( run it with no hood ) .i just want to see what the turbo gives me first to see if i should run it. :D :D
Members don't see the above ad. Register now - it's free!
Attachments
adam's 020.jpg
(952.58 KiB) Downloaded 121 times
adam's 019.jpg
(933.88 KiB) Downloaded 93 times
Last edited by alltracst185 on Tue Jul 15, 2014 11:57 pm, edited 52 times in total.
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

new wheels

Postby alltracst185 » Mon May 19, 2008 4:14 pm

so i thought the trac could use some flashier wheels , here they are. 18x9 in the rear and 18x8 in the front. what do you think?

Image
Attachments
new wheels.jpg
(68.45 KiB) Downloaded 85 times
Last edited by alltracst185 on Fri Nov 28, 2008 5:41 am, edited 1 time in total.
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

Postby Hotrodhendrix » Mon May 19, 2008 4:45 pm

They look good. What kind are they?

Also what kind of hood is that? Its off some from the original.
Last edited by Hotrodhendrix on Mon May 19, 2008 4:53 pm, edited 1 time in total.
"The more you let life's obstacles slow you down the longer it will take to defeat them."
~Yours truly
User avatar
Hotrodhendrix
GTFour God
 
Posts: 3480
Joined: Thu Sep 16, 2004 5:45 pm
Location: DFW Texas

Postby alltracst185 » Mon May 19, 2008 4:49 pm

the rims are axis and the hood is the seibon at style
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

Postby Hotrodhendrix » Mon May 19, 2008 4:53 pm

They arnt axis decades are they?? Thats funny. I picked some of these up for my alltrac saturday! :smokes:

Mine are 18x8 all the way around. The 18x9 fit the rear better than mine do.

How much did you get them for?
"The more you let life's obstacles slow you down the longer it will take to defeat them."
~Yours truly
User avatar
Hotrodhendrix
GTFour God
 
Posts: 3480
Joined: Thu Sep 16, 2004 5:45 pm
Location: DFW Texas

Postby alltracst185 » Mon May 19, 2008 9:08 pm

haha ya they are axis decades. ya with the 1" spacer still in there it fills the wheel well perfect :D i picked mine up for a steal at $500 with tires. i was amazed that the kid let them go for that :shock:
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

Postby MrDB » Tue May 20, 2008 8:46 am

ditch the top mount pronto or reach det city.. The top mount can only just cope with the std turbo let alone an uprated one.

Nice install though!
Image
Car Build : [ http://www.alltrac.net/phpBB2/viewtopic.php?f=44&t=26755 ]
MrDB
Club Member
 
Posts: 393
Joined: Fri Sep 28, 2007 6:22 am

Postby Hotrodhendrix » Tue May 20, 2008 12:50 pm

I second the motion for front mount...

I picked mine up for 550 with yokahoma parada spec 2 tires. The whole package only had about 5k miles on it. Very nice rims that look so much better in person.
"The more you let life's obstacles slow you down the longer it will take to defeat them."
~Yours truly
User avatar
Hotrodhendrix
GTFour God
 
Posts: 3480
Joined: Thu Sep 16, 2004 5:45 pm
Location: DFW Texas

Postby alltracst185 » Tue May 20, 2008 10:03 pm

i have a front mount, i have the bay area front mount kit with modified piping. i just got the rest of the fuel system. i got a speed source fuel rail rc 550 injecters and a aeromotive fpr waiting on the walboro 255 fuel pump and stainless lines and fittings. i also got alot more! i just have'nt been keeping up with my project all trac post. lol i'll post pictures of it all and update it soon.
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

Postby alltracst185 » Mon May 26, 2008 3:38 pm

so with the ems on the way i need to start installing my fuel system then celi is on her way to dsg for a good tune. :P can't wait to feel 18lbs of boost in the trac! pics comming soon
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

Postby klue » Mon May 26, 2008 4:06 pm

I like your set up. Im doing the same turbo, man even at 10 lbs it blows the ct26(lots more lag though :P)

But I have to comment on your wastegate. Where you have that dump tube entering the downpipe is not a good idea. Once you reach the boost you want and the WG lets go, its going to create some crazy turbulance insdie the exhaust, not to mention its right beside the turbine.
facebook.com/xiiimotorsports
#xiiimotorsports ON instagram
User avatar
klue
GTFour God
 
Posts: 3893
Joined: Thu Nov 04, 2004 9:47 pm
Location: Greater Toronto Area

Postby alltracst185 » Tue May 27, 2008 12:33 am

i plan to do a open dump very soon! i hate that it's recirculated back in. :shoots:
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

project alltracst185 update 6/6/08

Postby alltracst185 » Fri Jun 06, 2008 3:07 pm

well i've been spending alot of money lately, i got all the parts except for the braided fuel lines that run to the fpr and the fuel rail. my aem ems came in yesterday, i got the 255 walboro, aeromotive fpr, speed source fuel rail, rc 550 injecters, hks cam gears.( not sure if i want the hks cam belt or not) samco rad hoses, findanza flywheel all that need to be installed still. i just installed the cusco catch can, speed source extended push rod and egr block off plates, msd wires and blaster coil and one step colder plugs. finally had time to install the tial 38mm external wastegate and greddy profec b 11 right( thank god)currently holding 10lbs tight. so i just have to order arp head studs and bolts, install the fuel system, hks cam gears and then it's off to dsg to get tuned :D i do plan to do a full engine rebuild over the winter. i just would like to enjoy it at 18 lbs for a change.
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

Postby alltracst185 » Mon Aug 25, 2008 4:30 pm

so i got my cs bumper in this weekend, here is a pic of my car with no bumper

Image

and finnaly installed awaiting paint

Image
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

Postby alltracst185 » Mon Aug 25, 2008 4:32 pm

i'm still waiting on my arp head studs and hks timming belt from 935motorsports.com. then i could install the aem ems and bring it to get tuned :smokes:

this is a pic of all the stuff that needs to be installed

Image

sorry for the cell phone pics!
st185- HKS exhaust, Aussie mid pipe and custom 3" down pipe, Tial 50mm BOV, HKS 272 cams, HKS adj cam gears, custom FMIC, HKS GT3040, Tial 38mm wastegate, AEM ems, fully built bottom end, RC 1200cc injectors, at 25 lbs and almost complete :D
User avatar
alltracst185
Established Member
 
Posts: 2994
Joined: Sun Jan 14, 2007 8:27 pm
Location: Fitchburg, MA

Next

Return to My Project

Who is online

Users browsing this forum: No registered users and 4 guests