Hello everyone!
I have received quite a few inquiries about doing another run for the bushing kits. Everything is already been set up, so it should be a lot less work for me to make these for you guys(and thus less time between production). Lets see if we can have a successful run again for 10 or so. I am willing to buy two sets myself just to have them in case someone asks later. I understand that some people cant afford to wait as their cars are daily driven.
We did have a few issues on the last thread, hopefully everyone has their big boy pants on and we can keep this thread STRICTLY business. Please if you have any questions pertaining to the products post them here anything else does not belong on this thread.
Objectives: Replace worn out rear end bushings which cause excessive vibration, noise, sway, drive train mis alignment, and unwanted handling characteristics. Solidifying the rear end using the Acetal bushings gives the firmest connection to the rear end, with superior durability and material characteristics over nylon and polyurethane. Installing this complete kit will restore factory alignment in the drive train, improve throttle response and rear end feedback.
Thanks to Jordan for the picture
The features of our product:
- Finest quality and machining tolerance made right here in Canada with USA materials
-Bushings made of Acetal Copolymer certified to ASTM d6778 (Data sheets and mill test reports available )
-Diff plate made of aluminum 6061 alloy certified to ASTM b209 (Data sheets and mill test reports available )
To get your name on the group buy list you MUST send me a deposit of $30 USD. PM me for my paypal info.
I will be holding deposits via PAYPAL but accepting all major credit cards to avoid shortchanging myself with fees.
Your deposit will cover shipping charges to the USA, To Canada you will have $10 refunded to you
Email format is the following
*** At this stage in the group buy if there is interest in just the SUBFRAME, or just the DIFF kit we can accommodate this***
Name:
Username:
Phone number:
Complete shipping address:
Payment preferred:
Full Diff Upgrade kit ($365) USD
1. 801alltrac
2.
3.
4.
5.
6.
7.
8.
9.
10.
If anyone whom has PURCHASED a kit would like to leave some feedback on your experience good or bad please do. Only through you feedback can we improve our products for the alltrac community.
IF you do not pay by the deadline(TBA) you will loose your spot, and your deposit. I will not budge on this as I got screwed over the last run. Do not send your deposit if you can not make the payment when due.
Thank you guys for your support, as long as its there we can continue.
Tune in on Facebook
http://www.facebook.com/xiiimotorsports
Luke
Torque specs
Thanks Dave
I have received quite a few inquiries about doing another run for the bushing kits. Everything is already been set up, so it should be a lot less work for me to make these for you guys(and thus less time between production). Lets see if we can have a successful run again for 10 or so. I am willing to buy two sets myself just to have them in case someone asks later. I understand that some people cant afford to wait as their cars are daily driven.
We did have a few issues on the last thread, hopefully everyone has their big boy pants on and we can keep this thread STRICTLY business. Please if you have any questions pertaining to the products post them here anything else does not belong on this thread.
Objectives: Replace worn out rear end bushings which cause excessive vibration, noise, sway, drive train mis alignment, and unwanted handling characteristics. Solidifying the rear end using the Acetal bushings gives the firmest connection to the rear end, with superior durability and material characteristics over nylon and polyurethane. Installing this complete kit will restore factory alignment in the drive train, improve throttle response and rear end feedback.
Thanks to Jordan for the picture
The features of our product:
- Finest quality and machining tolerance made right here in Canada with USA materials
-Bushings made of Acetal Copolymer certified to ASTM d6778 (Data sheets and mill test reports available )
-Diff plate made of aluminum 6061 alloy certified to ASTM b209 (Data sheets and mill test reports available )
To get your name on the group buy list you MUST send me a deposit of $30 USD. PM me for my paypal info.
I will be holding deposits via PAYPAL but accepting all major credit cards to avoid shortchanging myself with fees.
Your deposit will cover shipping charges to the USA, To Canada you will have $10 refunded to you
Email format is the following
*** At this stage in the group buy if there is interest in just the SUBFRAME, or just the DIFF kit we can accommodate this***
Name:
Username:
Phone number:
Complete shipping address:
Payment preferred:
Full Diff Upgrade kit ($365) USD
1. 801alltrac
2.
3.
4.
5.
6.
7.
8.
9.
10.
If anyone whom has PURCHASED a kit would like to leave some feedback on your experience good or bad please do. Only through you feedback can we improve our products for the alltrac community.
IF you do not pay by the deadline(TBA) you will loose your spot, and your deposit. I will not budge on this as I got screwed over the last run. Do not send your deposit if you can not make the payment when due.
Thank you guys for your support, as long as its there we can continue.
Tune in on Facebook
http://www.facebook.com/xiiimotorsports
Luke
Torque specs
Thanks Dave