st185 body kit research and concepts (AT club homework)

CMS-GT4

Active member
Some potential there.

I went to a rallyx today and a wrx broke its spats and let me try it on Monk's alltrac. Its a close fit. Tey are from an 04 Sti.
 

Attachments

  • 10255021_10203702428506242_4893275801634132242_n-1.jpg
    10255021_10203702428506242_4893275801634132242_n-1.jpg
    94 KB · Views: 2,997
  • 10270306_10203702429226260_3951163760260225638_n.jpg
    10270306_10203702429226260_3951163760260225638_n.jpg
    96.8 KB · Views: 2,997
  • 10311790_10203702429546268_7367586690890168331_n.jpg
    10311790_10203702429546268_7367586690890168331_n.jpg
    102.3 KB · Views: 2,997

soarer.jzz30

New member
This is what happens when you convert a 92-93 bumper into an rc/cs and delete the blinkers and add a gen 1 focus lip...
 

Attachments

  • uploadfromtaptalk1402107129638.jpg
    uploadfromtaptalk1402107129638.jpg
    87.6 KB · Views: 2,938

CMS-GT4

Active member
Not keen on the tails, but with spats he was able to add a diffuser and get a rear lip look that covers the tank.
IMG_3773.jpg
 

soarer.jzz30

New member
Other than the spoiler and tails I like the rest, I wonder what the sides were made from, also the side rear splitters aren't my taste but looks pretty functional
 

CMS-GT4

Active member
Small adjustment through PS.
 

Attachments

  • 10455581_10152543388668593_7993931113816967224_n.jpg
    10455581_10152543388668593_7993931113816967224_n.jpg
    51.5 KB · Views: 2,859

CMS-GT4

Active member
If you ignore the diffuser you can see 205 rear spats used here on a 185.
 

Attachments

  • t1.jpeg
    t1.jpeg
    79 KB · Views: 2,847

soarer.jzz30

New member

Attachments

  • uploadfromtaptalk1405664078534.jpg
    uploadfromtaptalk1405664078534.jpg
    52.7 KB · Views: 2,694
  • uploadfromtaptalk1405664085965.jpg
    uploadfromtaptalk1405664085965.jpg
    82.7 KB · Views: 2,694
  • uploadfromtaptalk1405664102597.jpg
    uploadfromtaptalk1405664102597.jpg
    86.1 KB · Views: 2,694

CMS-GT4

Active member
So how you going to secure it? Bracket from the bottom?

For the PS I did of the Lancer spats, here is a cheap place for some reps if anyone wants to try it.
http://www.kaze-speed.com/exterior-body ... t-2pc.html

I also have my rear section on the way. I'll post pics of fitment once it gets here. Here is a quick PS of what I am expecting to pull off with the rear.
 

Attachments

  • Camaro-lip-205-skirt-ssiiispat.jpg
    Camaro-lip-205-skirt-ssiiispat.jpg
    296.4 KB · Views: 4,437
  • frontwindsplitter.jpg
    frontwindsplitter.jpg
    166.3 KB · Views: 4,437

soarer.jzz30

New member
The lip is terribly flimsy so I'm not sure a single bracket would suffice. I was debating trying 3m trim tape. Seems cheap but if done right it stays well. On the other hand... I could make a few small brackets to get it to fit right. There is a small ledge I could use some hardware and go from there. I also had an idea from this and the black car that used a stretched accord lip. Cheaper than the Evo pieces but a full wrap.
 

codytheoutlaw

New member
Does anyone know off hand if the All Trac or GTS spoiler will fit a GT with the narrow body and a lift back? I assume it will, but I didn't know if the wide body was any different on the section of the quarter panel where the sides of the spoiler mount. From what I can tell in the pictures, the wide body flares out closer to the wheel opening and the top part of the quarter looks like the narrow body.

Edit: After I posted this I found a GT Four narrow body and it has the wide body spoiler, so that answers my question.
 

CMS-GT4

Active member
SSiii spats came in, and they will not need as much work as I thought. Even the tabs line up with a place that can be mounted after drilling holes. One two sided tape will keep them tight. The main issue is a gap near the fender that needs to be resolved. Either some plastic filler or something might be worked out. Don't mind the gas tank cover, that is for another future project.
 

Attachments

  • IMG_6398.jpg
    IMG_6398.jpg
    159.1 KB · Views: 4,400
  • IMG_6401.jpg
    IMG_6401.jpg
    250.4 KB · Views: 4,400
  • IMG_6399.jpg
    IMG_6399.jpg
    257.3 KB · Views: 4,400

CMS-GT4

Active member
A couple more pics. I think I might make a rear piece that connects the two spats.
 

Attachments

  • IMG_6397.jpg
    IMG_6397.jpg
    175.2 KB · Views: 4,399
  • IMG_6406.jpg
    IMG_6406.jpg
    177.6 KB · Views: 4,399
Top