Page 1 of 2

Aftermarket wastegate for stock ct26?

PostPosted: Thu Jan 02, 2014 3:10 am
by Gordon12
Hi guys I was wondering if they make an aftermarket wastegate for a stock ct26? My engine is out of a 88-89 Alltrac. I bought a stock wastegate but was sold the wrong. Might as well just get a good one now.

Re: Aftermarket wastegate for stock ct26?

PostPosted: Thu Jan 02, 2014 4:22 pm
by MWP

Re: Aftermarket wastegate for stock ct26?

PostPosted: Thu Jan 02, 2014 4:47 pm
by Gordon12

Won't work. I've looked at those. The bracket on it has that curve to it. Like the wastegate I already tried to install.

Re: Aftermarket wastegate for stock ct26?

PostPosted: Thu Jan 02, 2014 4:48 pm
by Gordon12
uploadfromtaptalk1388684905009.jpg

Re: Aftermarket wastegate for stock ct26?

PostPosted: Thu Jan 02, 2014 4:49 pm
by Gordon12
Mine is the one on theft. Has to be something like that.

Re: Aftermarket wastegate for stock ct26?

PostPosted: Fri Jan 03, 2014 1:56 am
by MWP

Re: Aftermarket wastegate for stock ct26?

PostPosted: Fri Jan 03, 2014 2:04 am
by Gordon12
MWP wrote:http://www.ebay.com.au/itm/Kinugawa-Adjustable-Turbo-Actuator-TOYOTA-3S-GTE-GT4-ST165-CT26-/291044224835 ??

Says its for a ST165.

Curious. I didn't do the swap on my car. But I was told my turbo is out of a supra. Would that make a difference?

Re: Aftermarket wastegate for stock ct26?

PostPosted: Fri Jan 03, 2014 2:15 pm
by MWP
Quite possibly, yes.

Im not too familiar with gen1's or the ct26's used on Supra's though.
Someone else here should know more...

Re: Aftermarket wastegate for stock ct26?

PostPosted: Fri Jan 03, 2014 3:25 pm
by Gordon12
I hope someone does. Been dealing with this forever now and I just want to get it fixed :(

Re: Aftermarket wastegate for stock ct26?

PostPosted: Sat Jan 04, 2014 12:51 am
by SkagTits165
I know that when i put a supra ct26 on my 88 st165, i had to majorly change the stock actuator bracket to fit the supra one.

Re: Aftermarket wastegate for stock ct26?

PostPosted: Sat Jan 04, 2014 1:14 am
by Gordon12
vukawich wrote:I know that when i put a supra ct26 on my 88 st165, i had to majorly change the stock actuator bracket to fit the supra one.

Yeah that's what my motor is out of. 88 alltrac. Did your wastegate look like mine in picture? Currently installed is the one on left. The one with less of a curve.

Re: Aftermarket wastegate for stock ct26?

PostPosted: Sat Jan 04, 2014 2:38 am
by CSAlltrac
Forge makes a nice unit that utilizes the stock mounting arm. It requires you to remove the stock diaphragm, which is a bit of a pain in the ass to do cleanly, but it can be done.

Re: Aftermarket wastegate for stock ct26?

PostPosted: Sat Jan 04, 2014 3:03 am
by MWP
The Kinugawa actuators are screwed to the back of the supplied bracket.

You could remove the stock actuator from its bracket, then bolt the Kinugawa actuator onto it.

Re: Aftermarket wastegate for stock ct26?

PostPosted: Sat Jan 04, 2014 3:03 am
by Gordon12
CSAlltrac wrote:Forge makes a nice unit that utilizes the stock mounting arm. It requires you to remove the stock diaphragm, which is a bit of a pain in the ass to do cleanly, but it can be done.

If you have to use your old than what are you really buying? Just the bracket? Because my old wastegate is toast bad diaphragm believed.

Re: Aftermarket wastegate for stock ct26?

PostPosted: Sat Jan 04, 2014 3:35 am
by CSAlltrac
Gordon12 wrote:
CSAlltrac wrote:Forge makes a nice unit that utilizes the stock mounting arm. It requires you to remove the stock diaphragm, which is a bit of a pain in the ass to do cleanly, but it can be done.

If you have to use your old than what are you really buying? Just the bracket? Because my old wastegate is toast bad diaphragm believed.

You have to use the stock mounting hardware is what I'm saying. It replaces the diaphragm only, not the bracket.
http://www.forgemotorsport.com/content. ... ct=FMACGT4