[Toyota Part Numbers]

Conan

New member
Toxygene":3iyso1zc said:
Anyone have the part#'s for the ST185 Water to Air intercooler, the pump for the WTA intercooler, and the stock WTA radiator, and any wiring and hoses associated with that system?
You sure you wanna know all of this? :twisted:
185csic.gif
 

Khyron

New member
Is there an individual part # for the external housing for the fuel pump on a 90 ST185? I have the fuel pump's # but didn't know if the housing might have a separate #. If there is and if someone knows what that might be I'd really appreciate someone posting it. My housing is shot and w/o it there's no trac for me :(
 

d1alltrac

Active member
incase someone else needs them

ST165 Front Caliper Rebuild Kit---04479-20110
ST165 Rear Caliper Rebuild Kit---04479-33041


not sure if these were already posted or not but here are a couple more i got.

ST165 Clutch Master Cylinder---31410-20293
ST165 Clutch Slave Cylinder---31470-32032
 

toayoztan

Moderator
For anyone that's curious, i got these part numbers:

185 Head bolts - 90910-02094

HVAC (climate control cluster) lights w/ black socket - 81850-20180
HVAC lights with brown socket - 81850-20290

Bryan
 

Gary ST165

New member
ST165 Electronic Parts Catalogue(EPC):

PNC#15100B Part Number 15188-63010 RING, O (FOR OIL PUMP)

PNC#11155A Part Number 90253-10004 PIN, RING W/HEAD (dowel tube thing!)

PNC#13711A SEAL OR RING, O (for valve stem oil)
Part Number intake side 90913-02062
Part Number exhaust side 90913-02066

PNC#17173 GASKET, EXHAUST MANIFOLD TO HEAD Part Number 17173-88380

PNC#17177 GASKET, INTAKE MANIFOLD TO HEAD, NO.1 Part number 17177-88380

PNC#17179A GASKET, INTAKE MANIFOLD NO.2 Part number 17177-88380

PNC#13453 GEAR, FLYWHEEL RING Part Number 13452-74010 (SUBS) 1345-74011


please confirm all part#'s with your Toyota dealer etc in case of my bad!!!


i haven't tried this myself yet, but i am led to believe that the EPC can be downloaded from here: http://ugbox.net/~lance/GT4/Technical/EPC/

as reported by forum users in this thread: http://www.grparallye.com/forums/viewto ... hlight=epc

regards
 

BLOWNTACO

New member
RC/CS engine under covers
51408-20040
51408-20050

RC emblem
75444-2B240

RC/CS Fan blade
16361-55010

RC/CS Fan motor
16363-74070

Rain Visors:
08613-20130
 

maxaud

Active member
maxaud":r4la8419 said:
what about the side stickers, my drivers side one has a little piece taken out of it.

ok, I guess I found the answer to my own question... I like it when that happens...

75097-20040-10 grey LH
75099-20040-10 grey RH
75097-20040-15 black LH
75099-20040-15 black RH
(found these in another thread)

what one will I need for my car? It's black. Does that mean I need the black sticker oris the sticker itself black? anyone know?
 

maxaud

Active member
I also found these...
75097 - 20010 - 13
75099 - 20010 - 13
anyone know if these are correct?
 

Denver_whiteST185

New member
BLOWNTACO":7eeyf40h said:
RC/CS engine under covers
51408-20040
51408-20050

RC/CS Fan blade
16361-55010

RC/CS Fan motor
16363-74070

Hey, im wondering if the RC fan motor/blade assembly was any better than the stock USDM one. i think i remember hearing that it was more powerful. can someone confirm this and also point me in the right direction of getting one. Also, were the RC undercovers any different than the stock ones???
 

maxaud

Active member
160 watt rather then 120 watt. RC undercover (assuming that is the heat shield/noise dampener) is way different then stock All-trac. It has openings for front grille, back holes and timing chain cooler.
 

alltracman78

Active member
Denver_whiteST185":2f36wba1 said:
If i sent you my extra USDM fan/shroud, would you compare/test fit the two???

There are 6 blades instead of 4 on the RC fan.
The motor is of course higher power.

The shroud is the same.
 

Meurz

New member
90240-06017 = One of 2 pins that go through a Supra JZA80 rear brake calliper to keep the brakepads in place. I bought these cause I needed new ones for my ST205 rears.. same part :D
 

BLOWNTACO

New member
Hey, just installed the RC fan and motor in my All-Trac. Fits great!! The only thing is the USDM screws don't work with JDM motor. Quick fix though, grab some small metric bolts; nuts; lock washers and plain old washers. Use some locktite on the threads to make sure they don't vibrate loose, and viola! :D
 
Top