st185 oil failure/bearings video
9 posts
• Page 1 of 1
st185 oil failure/bearings video
Hi,
I am new to celica st185 world. Second time my engine is blown in short time.
its basically second time, engine bearings failure... repair was done really properly. Cranc was done -0,5, Measured tolerance, 0,029mm and crank turned freely etc, all by the book.
I didnt have time yet to put oil pressure sensor and oil temp sensor to engine. Is there some oilpump failure/issues that could be known to 3sgte? Is this driving too rough for 3sgte? ... oil temp? pressure? Motor temperature was according to gage fine. Is the rpm too high? What would be most likely cause bearing failure second time driving as shown?
http://www.youtube.com/watch?v=CxplrKCdPjk&feature=youtube_gdata
I am new to celica st185 world. Second time my engine is blown in short time.
its basically second time, engine bearings failure... repair was done really properly. Cranc was done -0,5, Measured tolerance, 0,029mm and crank turned freely etc, all by the book.
I didnt have time yet to put oil pressure sensor and oil temp sensor to engine. Is there some oilpump failure/issues that could be known to 3sgte? Is this driving too rough for 3sgte? ... oil temp? pressure? Motor temperature was according to gage fine. Is the rpm too high? What would be most likely cause bearing failure second time driving as shown?
http://www.youtube.com/watch?v=CxplrKCdPjk&feature=youtube_gdata
Members don't see the above ad. Register now - it's free! | |
- lordvampire
- Club Member
- Posts: 41
- Joined: Sun Oct 20, 2013 7:11 am
Re: st185 oil failure/bearings video
I just rebuilt my engine and had it make it 50 miles before loosing oil pressure when its warm. My bearings are grinded up pretty decent. Was a full tear down and rebuild and refresh done pretty properly and a reputable machine shop doing the machine work. Only thing we can come up with was the bearings lost their prelube before the engine was able to get started. That is, if during your first crank, the engine doesn't fire and start and run within under minute then lube on the bearings will run out and it will grind them, causing problems shortly there after.
I don't think that driving could be nearly too rough, assuming everything was in good condition and you had full oil. If your oil level was low you could maybe suck air on a turn, but I'd think you notice. Maybe get a pan with a sump if your that worried about it, but nothing wrong that I can see...
I don't think that driving could be nearly too rough, assuming everything was in good condition and you had full oil. If your oil level was low you could maybe suck air on a turn, but I'd think you notice. Maybe get a pan with a sump if your that worried about it, but nothing wrong that I can see...
-
Fox 21 Alpha - Club Member
- Posts: 256
- Joined: Sat Aug 23, 2008 5:21 am
- Location: PA
Re: st185 oil failure/bearings video
Thx for replay. Yes, oil was in max level. Semi-synt Castrol.
- lordvampire
- Club Member
- Posts: 41
- Joined: Sun Oct 20, 2013 7:11 am
Re: st185 oil failure/bearings video
what I like to do when I build my motors is spin the oil pump with oil in it. this is pre-installing the timing belt. I would hook up my cordless drill with a 12mm socket and rotate in clockwise as fast as it can go. this will lube up all bearings as well as the cam journals.

I <3 MY ST214
-
celicast184 - Club Member
- Posts: 733
- Images: 0
- Joined: Fri May 16, 2008 5:05 pm
Re: st185 oil failure/bearings video
Ok, tnx, good tip, new oilpump maybe too?... To be sure?
- lordvampire
- Club Member
- Posts: 41
- Joined: Sun Oct 20, 2013 7:11 am
Re: st185 oil failure/bearings video
Make sure to get the oil cooler nice and clean too it has a tendency to hold metal shavings, also get the rods checked for out--of-roundness the main side will spread when unbolted.
- 90blacktrac
- Club Member
- Posts: 246
- Images: 26
- Joined: Sun Jun 04, 2006 3:44 am
- Location: Iowa
Re: st185 oil failure/bearings video
Second time second rod bearing. And rod is also wasted (oval). Rod was replaced the other time. So again second rod+bearing. I dont know, maybe there was somewhere some metal shavings left. It was cleaned, but, dont come up with no other reason. Why second and same way?


Oh well... engine out ... here we go again. lets try again, and with all cautions


Oh well... engine out ... here we go again. lets try again, and with all cautions

- lordvampire
- Club Member
- Posts: 41
- Joined: Sun Oct 20, 2013 7:11 am
Re: st185 oil failure/bearings video
Does 3sgte gen1 (st165) oil pump fit to gen2? Is it same good? Have lowmilage engine, where to take spare parts...
- lordvampire
- Club Member
- Posts: 41
- Joined: Sun Oct 20, 2013 7:11 am
Re: st185 oil failure/bearings video
Is it possible, that cylinders are not in round? Previous owner has changed pistons(new standard), maybe with heat piston seizes and cause the failure. I dont see why would conrod go bad other way. ?
- lordvampire
- Club Member
- Posts: 41
- Joined: Sun Oct 20, 2013 7:11 am
9 posts
• Page 1 of 1
Return to Performance and Power
Who is online
Users browsing this forum: No registered users and 1 guest